Please wait while the page loads...

Will the check engine light reset itself?

The check engine light on your 2014 Toyota Sequoia will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going functional, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2014 Toyota Sequoia light will go off after about 20-40 miles. If you drive over that reward and the light is still on, you will need to bring it in to Nalley Toyota of Roswell so the light and code can be double-checked and reset.

Check Engine Light Service 2014 Toyota Sequoia

What do you do when you’re driving along in your Toyota Sequoia and immediately, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Toyota owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t pick you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2014 Toyota Sequoia checked as soon as attainable. Ignoring that warning could end up causing dynamic wear and tear to expensive engine components.

When your 2014 Toyota Sequoia's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t legitimate, a computer turns on your check engine light. This amber or yellow light is normally labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic diagnose tool that is used by our Toyota auto repair mechanics at Nalley Toyota of Roswell. There are also a number of rather inexpensive code readers that are designed for do-it-yourselfers, should you favor that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an skilled skilled to favor the issue and repair it.

2014 Toyota Sequoia Check Engine Light

If the check engine light in your 2014 Toyota Sequoia starts flashing, that means that the problem needs immediate attention and your Toyota should be brought in immediately. A flashing light illustrates that the problem is perilous and if not taken care of immediately may result in gigantic damage to the vehicle. This glaring light frequently indicates a exacting engine misfire allowing unburned fuel to be deposited into the exhaust system. There it can quickly boost the temperature of the catalytic converter to a point where damage is viable, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can exactly be the cause. A harmful, aged or dirty spark plug can cause the engine to misfire. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a exceedingly expensive repair. If your check engine light is flashing, please contact our unit of automotive experts at Nalley Toyota of Roswell immediately by calling 7707637398.

What could cause the check engine light to come on in a 2014 Toyota Sequoia?

When your check engine light comes on, this could be as clear-cut as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a critical problem that could cause critical damage to your engine and come with a extraordinary repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow normally means something less critical but a flashing check engine light implies that your vehicle’s engine is in critical trouble and service is necessary at this moment. If your check engine light is flashing in your 2014 Toyota Sequoia, we particularly illustrate not to drive the vehicle and schedule Toyota service today. Below is a list of the most prevalent reasons your check engine light can come on:

  • One of the most modern and copious cause is that your 2014 Toyota Sequoia gas cap is loose, damaged or missing. The gas cap for your 2014 Toyota Sequoia serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is aged or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on straightaway after you put gas in your 2014 Toyota Sequoia, first thing you should check is to make sure the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2014 Toyota Sequoia’s exhaust system. The catalytic converter's perform is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Nalley Toyota of Roswell offers a complimentary multi-point inspection with every Toyota service. If you have an issue with your catalytic converter and don't get it repaired, your 2014 Toyota Sequoia will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other problems from overheating.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Toyota Sequoia is what determines how much fuel is essential to run your engine efficiently by measuring the reward of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to conscious changes, like altitude. If your Toyota Sequoia is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • The battery is low or dead. The battery in your 2014 Toyota Sequoia is every satisfied. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did assorted decades ago, and they don't absolutely require maintenance. The price of a new one depends on the type of Toyota you drive, but check our actual service coupons and specials.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the reward of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less accessible when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2014 Toyota Sequoia's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to opt for the right mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • New Spark Plugs or Plug Wires are essential for your 2014 Toyota Sequoia. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or aged, you will experience poor performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, major to more expensive repairs.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak havoc on your 2014 Toyota Sequoia if it’s not installed appropriately. These aftermarket parts and accessories can discharge the battery, trigger the check engine light, or even avert the vehicle from starting. If these issues sound chummy, bring your Sequoia to Toyota and have our squad of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might cost a miniature bit more but could save you money from having to get poor perform and damage caused by poor installation perform corrected.
  • Your 2014 Toyota Sequoia has a vacuum leak. Every Toyota Sequoia has a vacuum system that performs a roomy variety of functions. The vacuum system also helps lower bad emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, especially if they’re exposed to splendid heat or extreme cold.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not accurately tightened to a more noticeable failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it extraordinary to get the lawful code reading and diagnosis. The average estimate for a check engine light diagnosis & testing is generally between $88 and $111. The extraordinary news, Nalley Toyota of Roswell offers complimentary multi-point inspections and free diagnostics, in most cases, to help indicate the cause of your check engine light.

2014 Toyota Sequoia Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that tiny light on your vehicle’s dashboard suddenly illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Sequoia. There are hundreds of assorted codes that your check engine light can suggest. While that sounds daunting, with a tiny patience, tackling basic diagnostics will give you vital knowledge about your vehicle and will also allow that Check Engine Light to do what it is genuinely supposed to do: be your guide. Unfortunately, overt and vital vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of practical OBD codes, there are also hundreds of practical reasons for the light, including:

  • Fuel and air metering systems problems
  • Loose Gas Cap or Missing Gas Cap
  • Ignition system faults
  • Bad Spark Plugs
  • Computer output circuit issues
  • Transmission issues
  • Emissions controls issues
  • O2 Sensor
  • Old Battery

This is why it is critical for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a perilous concern, you risk damaging your car further by not repairing the issue right away. When your check engine light comes on, you should get it checked out urgently by a certified Toyota mechanic. Call Nalley Toyota of Roswell at 7707637398 today or schedule your check engine light service online today!

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is difficult to predict how frequent miles you can drive with the warning light on. It could be anything from a bad sensor to plug wires needing to be replaced. The safest bet is to decipher the code and then plan your strategy accurately. If you check engine light is blinking, we recommend that you pull over and contact Nalley Toyota of Roswell to help read if your vehicle is safe to drive in or if we recommend a tow truck.

What Does the Check Engine Light Mean?

One of the most mostly misunderstood lights or indicators in your 2014 Toyota Sequoia is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in several supplemental ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your 2014 Toyota Sequoia. Some of these include shifting automatic transmissions controlling engine speed, ignition timing, and implementing stability control, just to name a few. With that being said, the check engine light can mean a collection of distinctive things. It can be as prevalent as your gas cap being loose or as curious as engine knocking. If your check engine light is on in your 2014 Toyota Sequoia, contact Nalley Toyota of Roswell. Our Toyota service department can help you learn what code is turning your check engine light on or diagnose why your check engine light is flashing. Contact Nalley Toyota of Roswell today!

2014 Toyota Sequoia Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are countless established causes including something as authentic as a loose gas cap. Back-up established reasons for a Check Engine Light are faulty head gasket, damaged oxygen sensor, dirty mass airflow sensor, a malfunction with the fuel injection system, faulty emissions control part, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Toyota Certified Technicians and the certified service protocol to isolate the root problem and repair it as decisive to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Toyota issue was fixed.

Every 2014 Toyota Sequoia was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the car on its hard systems. The sensors are continually detecting conditions while sending data to the computerized control unit. If the computerized control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is culpable nor what to do about it. That’s where we come in; Nalley Toyota of Roswell provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Largely Qualified Service professional.

Is it safe to drive your 2014 Toyota Sequoia with the check engine light on?

This question is not very effortless because it each depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be applicable to drive. This is continuously indicated by a consistent glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more evident problem. If the check engine light is glaring, this means that there is a evident issue and it is recommended to service your Toyota Sequoia expeditiously. Call the specialists at Nalley Toyota of Roswell by dialing 7707637398 so you can describe the issues. Or cut your speed and bring your 2014 Toyota to our certified mechanics as soon as achievable.