Please wait while the page loads...

2013 Toyota Sequoia Check Engine Light Flashing

Although there are several viable causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several known causes including something as plain as a loose gas cap. Other known reasons for a Check Engine Light are dirty mass airflow sensor, a malfunction with the fuel injection system, damaged oxygen sensor, faulty emissions control part, faulty head gasket, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Toyota Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Toyota issue was fixed.

Every 2013 Toyota Sequoia was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its crucial systems. The sensors are usually detecting conditions while sending data to the electronic control team. If the electronic control team detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what absolutely is amiss nor what to do about it. That’s where we come in; Nalley Toyota of Roswell provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Very Qualified Service professional.

2013 Toyota Sequoia Check Engine Light

A flashing light suggests that the problem is serious and if not taken care of expeditiously may result in major damage to the vehicle. If the check engine light in your 2013 Toyota Sequoia starts flashing, that means that the problem needs hasty attention and your Toyota should be brought in expeditiously. This flashing light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can quickly raise the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can solely be the cause. A bad, former or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our team of automotive veterans at Nalley Toyota of Roswell instantly by calling 7707637398. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a particularly expensive repair.

How many miles can you drive with the check engine light?

Since any check engine code has its own level of severity, it is difficult to predict how many miles you can commute with the warning light on. If you check engine light is blinking, we advocate that you pull over and contact Nalley Toyota of Roswell to help mean if your vehicle is steady to commute in or if we advocate a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. It could be anything from a destructive sensor to plug wires needing to be replaced.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more serious failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it satisfied to get the apt code reading and diagnosis. The average cost for a check engine light diagnosis & testing is typically between $88 and $111. The satisfied news, Nalley Toyota of Roswell offers complimentary multi-point inspections and free diagnostics, in most cases, to help mean the cause of your check engine light.

Check Engine Light Service 2013 Toyota Sequoia

What do you do when you’re driving along in your Toyota Sequoia and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Toyota owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t imply you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Toyota Sequoia checked as soon as functional. Ignoring that warning could end up causing major damage to expensive engine parts.

When your 2013 Toyota Sequoia's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t decent, a computer turns on your check engine light. This amber or yellow light is generally labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Toyota auto repair mechanics at Nalley Toyota of Roswell. There are also a number of rather inexpensive code readers that are designed for do-it-yourselfers, should you elect for that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced active to indicate the issue and repair it.

2013 Toyota Sequoia Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard hastily illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Sequoia. There are hundreds of divergent codes that your check engine light can represent. While that sounds daunting, with a little patience, tackling main diagnostics will give you advantageous knowledge about your vehicle and will also allow that Check Engine Light to do what it is actually supposed to do: be your guide. Unfortunately, visible and advantageous vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of achievable OBD codes, there are also hundreds of achievable reasons for the light, including:

  • Computer output circuit issues
  • Bad Spark Plugs
  • Emissions controls issues
  • Fuel and air metering systems problems
  • Loose Gas Cap or Missing Gas Cap
  • Transmission issues
  • Old Battery
  • Ignition system faults
  • O2 Sensor

This is why it is suitable for someone who does not have various of automotive knowledge to not assume what a code means. Call Nalley Toyota of Roswell at 7707637398 immediately or schedule your check engine light service online today! If the engine light comes on due to a serious concern, you risk damaging your car additional by not repairing the issue right away. When your check engine light comes on, you should get it checked out quickly by a certified Toyota mechanic.

Is it safe to drive your 2013 Toyota Sequoia with the check engine light on?

If the check engine light is flashing, this means that there is a momentous issue and it is recommended to service your Toyota Sequoia quickly. This question is not excessively simple because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is generally indicated by a dependable glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more fascinating problem. Call the experts at Nalley Toyota of Roswell by dialing 7707637398 so you can describe the issues. Or reduce your speed and bring your 2013 Toyota to our certified mechanics as soon as available.

What could cause the check engine light to come on in a 2013 Toyota Sequoia?

When your check engine light comes on, this could be as compelling as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a alarming problem that could cause alarming damage to your engine and come with a gigantic repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow continually means something less alarming but a twinkling check engine light indicates that your vehicle’s engine is in alarming trouble and service is mandatory quickly. If your check engine light is twinkling in your 2013 Toyota Sequoia, we highly indicate not to drive the automobile and schedule Toyota service today. Below is a list of the most commonplace reasons your check engine light can come on:

  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Toyota Sequoia is what determines how much fuel is fundamental to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to good changes, like altitude. If your Toyota Sequoia is having trouble starting, idling rough or has a brisk change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • The battery is low or dead. The battery in your 2013 Toyota Sequoia is every crucial. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't really require maintenance. The price of a new one depends on the type of Toyota you travel to work, but check our present service coupons and specials.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Toyota Sequoia’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Nalley Toyota of Roswell offers a complimentary multi-point inspection with every Toyota service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Toyota Sequoia will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other problems from overheating.
  • New Spark Plugs or Plug Wires are fundamental for your 2013 Toyota Sequoia. The spark plugs are the part of your engine that ignites the air/fuel variety in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or old, you will experience meager performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, essential to more expensive repairs.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, accepted as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less adequate when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2013 Toyota Sequoia's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to indicate the right variety of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak havoc on your 2013 Toyota Sequoia if it’s not installed accurately. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound accepted, bring your Sequoia to Toyota and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, chiefly aftermarket parts and accessories, or using OEM parts first place might value a tiny bit more but could save you money from having to get meager work and damage caused by meager installation work corrected.
  • Your 2013 Toyota Sequoia has a vacuum leak. Every Toyota Sequoia has a vacuum system that performs a wide variety of functions. The vacuum system also helps lower damaging emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, chiefly if they’re exposed to important heat or extreme crisp.
  • One of the most respectable and frequent cause is that your 2013 Toyota Sequoia gas cap is loose, damaged or missing. The gas cap for your 2013 Toyota Sequoia serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is old or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on immediately after you put gas in your 2013 Toyota Sequoia, first thing you should check is to make convinced the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.

What Does the Check Engine Light Mean?

One of the most generally misunderstood lights or indicators in your 2013 Toyota Sequoia is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few distinctive ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a fluctuate of things for your 2013 Toyota Sequoia. Some of these include controlling engine speed, shifting automatic transmissions ignition timing, and implementing stability control, just to name a few. With that being said, the check engine light can mean a collection of discrete things. It can be as delightful as your gas cap being loose or as relentless as engine knocking. If your check engine light is on in your 2013 Toyota Sequoia, contact Nalley Toyota of Roswell. Our Toyota service department can help you find out what code is turning your check engine light on or audit why your check engine light is flashing. Contact Nalley Toyota of Roswell today!

Will the check engine light reset itself?

The check engine light on your 2013 Toyota Sequoia will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going factual, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Toyota Sequoia light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Nalley Toyota of Roswell so the light and code can be double-checked and reset.